Ace Glass 12106-10 Temperature
Controller, Time Proportional, Digital. (Inv 
#8083)
Digital temperature unit features selectable front 20v/40v outlet,
and rear 120v outlet, RTD Sensor Input. LlCD Digital Readout lets
you dial up the desired temperature. Dim: H x W x D; 9.75"
x 5.5" x 10". Unit wt. 17 lbs. Very good used condition,
fully checked, cleaned, guaranteed. Included RTD probe in fair,
dented condition, yet fully functional. Price: $425.00
Ace Glass 12110-06 Temperature
Controller Time Proportional, Digital Set & 
Readout.
(Inv #8082) Bench model, LED digital, time proportional, temperature
controller. Calibration, span, etc. settable by screws under easy
access door at bottom of panel. Unit is designed with multiple
outlets; one rear 120V, and one selectable 20/40V front outlet,
and one Type ”J” thermocouple probe outlet. Temperature
range is -50° to 500º C with 1° C resolution. Unit
has convenient carrying handle. Power req.120V 15A, 50/60 Hz input.
Dim: 9.75"H x 5.5"W x 10" D; weight = 17 lbs. Very
good used condition, fully checked, cleaned, guaranteed. Price:
$295.00
Hart Scientific Model 9112 Calibration
Furnace. (Inv #7883) The Hart 9112 
Calibration
Furnace was designed specifically for calibrating PRTs, fiber
optic sensors and thermocouples at higher temperature ranges up
to 1100 deg C. The furnace utilizes an equilibration block capable
of making comparison measurements on multiple probes. The included
standard equilibration block is sized for 1/4" probes. The
temperature stability is better than +/- 0.1 deg C throughout
the range and the gradient between wells at full insertion is
less than 0.5 deg C +/-0.25 deg C. Temperature is set with convenient
up/down buttons on the digital display. There is a separate adjustable
over-temp cut-out to protect your probes from over-temp situations
and the furnace itself from the possibility of thermal runaway.
Operating Range: 300 deg C to 1100 deg C, Stability: 300 to 500
deg C: +/- 0.05 deg C, >500 to 1100 deg C: +/- 0.1 deg C, Uniformity:
+/- 0.05 deg C at 300 deg C to +/- 0.3 deg C at 1100 deg C, Stabilization
Time: typical 2 hours at mid-range, up to 4 hours at low range,
faster at high range, Heater Power: 3700 Watts High Range, 925
Watts Low Range, Power Requirements: 230 VAC, 50/60 Hz, 20A, Outside
Dimensions: 18" H X 14.25" W X 26" D. Excellent
used condition, checked, guaranteed. Price: $7195.00
J-Kem Scientific Gemini-K
Dual Channel Controller. (Inv #8604) Dual-channel 
controller
features two temperature controllers in a single cabinet to regulate
two independent reactions using type-K thermocouples. Accepts
std. and mini thermocouple plugs. Channel 1 also has a 100 hour
digital timer to turn heating OFF (or ON) at a user entered time.
Includes over-temperature protection circuits with audible alarms,
dual temperature displays, selectable operating modes, double
fused, and 100% solid state design. Patented power control computer
which provides 0.1°C regulation of anything. This fine control
with 5 independent settings can be set for volumes as low as 1-10ml,
10-100ml, 50-500ml, 300-2L, to 2L+ while maintaining that 0.1°C
regulation. User programmable for different heating applications
e.g. hotplate, oven, mantle, as well as ramp, hold/soak, and automatic
shutoff. With a clamp for support stand mounting. Power specs,
120V, 60Hz, 1200W max per channel. Excellent used condition, fully
checked, cleaned, guaranteed. Includes Manual. Price: $525.00
Omega ICSS-116G-12-PFA Type J
Thermocouple, PFA 
PTFE
Coated Probe. (Inv #8560) Sheath Diameter : 1/16 Inch, Sheath
Length : 12 Inches, Termination : Grounded. New-in-Box. Price:
$24.95
Omega CASS-116G-12-PFA Type K Thermocouple, PFA PTFE Coated Probe. (Inv #8561) Sheath Diameter : 1/16 Inch, Sheath Length : 12 Inches, Termination : Grounded. New-in-Box. Price: $24.95
Omega Engineering Model SJP-1-06
Thermocouple Jack Panel Box. (Inv #5459) Single row of six
jacks, 8 foot 
leads,
for Type J thermocouples. Unused surplus, guaranteed. Price: $20.00
Omega Engineering Model SJP-2-12
Thermocouple Jack Panel Box. (Inv #5460) Two rows of six 
jacks
(12 jacks total) 8 foot leads, for Type J thermocouples. Unused
surplus, guaranteed. Price: $40.00
Omega Engineering Portable Digital
Thermocouple (K) Thermometer. (Inv #7052) Light-weight portable
Celsius thermometer with digital display. 
Optional
analog output terminals on rear. Carrying handle doubles as an
adjustable stand for unit. Specs: K-thermocouple, -50C to 1250C,
with 1C resolution. Power req: 115V, 50/60Hz. Very good used condition
with a scratch on display (does not affect readability), checked,
guaranteed. Price: $115.00.
Raytech Portable Infra-red Thermometer
Model Raynger ST Pro. (Inv # Multiple) This high quality hand
held IR thermometer allows for quick easy 
non-contact
temperature measurements of surfaces. From professionals to homeowners,
this tool allows easy research of heating and ventilation problems,
and can be used to monitor electric motor status, diagnose automotive
problems, and monitor food temperatures for safety. Features include:
measurement range -32C to 535C (-25F to 999F) with 0.1degree resolution,
high resolution optics, accuracy of 1% with 0.5% repeatability,
max temperature display, laser sighting, and a backlit display.
Laser allows you to zero in on your target, and within 1 second
the display indicates current and maximum surface temperatures.
Raytech is now a division of Fluke.
(Inv #'s 7036-7041) Like new condition, checked, guaranteed. Price: $99.00
(Inv #'s 7021-7024, 7027-7029, 7032, 7042) Very good used condition, checked, guaranteed. Price: $79.00
Transmation Model 1045 Digital
Calibrator and Signal Indicator. (Inv 
#7766,
7767) The Model 1045 can simulate and/or measure current or voltage
signals that fall within the millivolt, volt, and milliamp ranges
as indicated in the chart below. Input and Output signal values
are indicated on the front-panel four-digit liquid crystal display.
Each signal type has a separate set of terminals for input and
output connections permitting simultaneous input and output operations.
Extremely versatile, the Model 1045, in addition to simultaneous
process signal simulation/measurement, can simulate a two-wire
transmitter. It can also measure the output of a two-wire transmitter
while simultaneously powering the transmitter from the 1045's
own 24 VDC supply. Very good used condition, brand-new Nicad battery
packs, includes case and charger, checked, guaranteed. Price:
$765.00
|
|
|
|
|
|
| Input |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Output |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Chromalox Model MTO-110A Immersion
Heater, 1KW. (Inv #7366) 
Designed
for light weight oil baths or tanks, this heater is equipped with
12-1/2 long dual steel sheath elements and a 1.25in NPT screw
thread mount. Power req: 120V, 1000W, 1ph. Unused surplus, guaranteed.
Price: $75.00
Cleveland Process Corp. Model
#WS1107 Single Tube Bayonet 
Immersion
Heater. (Inv #7283) 304 Stainless Steel immersion tube heater
will work in environments as diverse as an alkali electro-cleaning
tank to a serene koi pond. Controller required; it is available
from the manufacturer. Power req. 120V, 60Hz, 1000W. New or like-new
condition, guaranteed. Price: $35.00
Glo Quartz Electric Heater Model#
N-2DD19. (Inv# 7365M) Single Tube 
Heater
240V/1P, 19" long tube with an 11" heated zone. Solution
should be kept 2” above the heated length at all times.Type
N: Low watt density, 20 watts/sq. inch - for Heat sensitive or
heavy acid solutions such as nickel plating, electropolishing
or phosphoric acid. NOT recommended for alkaline or caustic solutions.
Heater is supplied with a preset over-temperature switch encased
in a teflon® tube that runs vertically along the outside of
the quartz tube. This switch should be used with the TC series
temperature controls or equivalent. Maximum solution operation
temperature is 200ºF. Power req. 240V, 50/60Hz, 1000W, 1Ph.
New-in-package. Price: $95.00ea., 2 or more, $88.00ea.
Process Technology Model# HXSL-5108X
Flex Riser Fluoropolymer 
(PTFE)
Heater- 500W. (Inv #7367) The superior chemical resistance
of this heater makes it inert to most aqueous acid, alkaline,
anodizing and pickling solutions up to 212°F (100°C).
The rugged construction of heavy wall fluoropolymer (PTFE) covered
stainless steel element reduces permeation and eliminates the
need for gas purge systems. Guaranteed 100% pinhole free. Outstanding
low watt density design (10 watts/square inch, 1.5w/cm2) for long
service life. 8" x 8" square 500W heating element with
a 6" riser, with spacers fits a 9" to 12" square
bath, to a maximum working depth of 5".
Safety features:
• Grounded internal metal element.
• Thermal protector built in. Resettable PIII J-type thermocouple
standard.
• Non-floating construction.
Power req. 120V, 50/60, 500W. New-in-package. Price:$195.00